Справка Houdini на русском Nodes Dynamics nodes

Constraint Relationship dynamics node

On this page

The Constraint Relationship DOP encapsulates some of the most common constraint relationship setups into a single convenient asset. This node is used in all the RBD and Cloth Constraint assets to provide a common set of parameters for controlling the constraint relationship.

This asset does not provide a complete set of all possible constraint relationships. In particular the two state relationship has many more possible configurations than the ones exposed by this asset. See the help for the separate constraint relationship nodes for more information.

Parameters

Relationship

Relationship Type

How Houdini constrains the object to the goal point.

Hard Constraint

Keeps a constant distance between the object and the goal, as if they were attached by a rigid wire.

Spring Constraint

Constrains the object as if it was attached to the goal by a spring.

The Spring Strength parameter controls how much the spring constrains the object. If this value is too low, the spring will not be able to pull the object, and it will act as if it wasn’t constrained at all.

For a 1 unit object at the default density, the spring strength should be around 3000-8000 to hold up an object against default gravity.

Increase Spring Damping to decrease unwanted oscillation and yo-yoing of the object.

Two State Constraint

Acts as a hard constraint until certain forces are met, then acts like a spring constraint.

The constraint switches between a hard and a spring constraint based on the motion of the constrained object:

  • When the constraint is hard, if the "pull" of the object goes beyond the Two State Max Force value, the hard constraint will "let go" and turn into a spring constraint.

  • When the constraint is a spring, if the object gets within the Two State Min Distance of the goal, the spring will turn into a hard constraint.

Two State Initial State

When using a two state constraint relationship, this parameter controls whether the constraint starts as a hard constraint or as a spring constraint.

Hard Constraint

The two state constraint is initially treated like a hard constraint.

Spring Constraint

The two state constraint is initially treated like a spring constraint.

Two State Max Force

Sets the force threshold for changing a two state constraint from the hard constraint state to the spring constraint state.

Two State Min Distance

Sets the distance threshold for changing a two state constraint from the spring constraint state to the hard constraint state.

Spring Strength

Controls how strongly the spring constraint acts on the constrained object to return the anchors to the rest length separation.

Spring Damping

Controls the amount of damping in the spring relationship. As damping increases, the spring constraint acts more slowly and oscillates less.

Spring Rest Length

Sets the rest length of the spring relationship. The force applied on a constrained object by a solver will tend to keep the object this distance away from the goal.

Guide Options

Radius

Controls the radius of the spheres drawn in the viewport as guide geometry for this constraint.

Hard Color

If this is a hard constraint relationship, this parameter controls the color of the guide geometry. Using different colors for hard and spring constraint relationships makes it easy to see when a two state constraint switches from one state to the other.

Spring Color

If this is a spring constraint relationship, this parameter controls the color of the guide geometry.

Inputs

Outputs

Locals

channelname

This DOP node defines a local variable for each channel and parameter on the Data Options page, with the same name as the channel. So for example, the node may have channels for Position (positionx, positiony, positionz) and a parameter for an object name (objectname).

Then there will also be local variables with the names positionx, positiony, positionz, and objectname. These variables will evaluate to the previous value for that parameter.

This previous value is always stored as part of the data attached to the object being processed. This is essentially a shortcut for a dopfield expression like:

dopfield($DOPNET, $OBJID, dataName, "Options", 0, channelname)

If the data does not already exist, then a value of zero or an empty string will be returned.

DATACT

This value is the simulation time (see variable ST) at which the current data was created. This value may not be the same as the current simulation time if this node is modifying existing data, rather than creating new data.

DATACF

This value is the simulation frame (see variable SF) at which the current data was created. This value may not be the same as the current simulation frame if this node is modifying existing data, rather than creating new data.

RELNAME

This value will be set only when data is being attached to a relationship (such as when Constraint Anchor DOP is connected to the second, third, of fourth inputs of a Constraint DOP).

In this case, this value is set to the name of the relationship the data to which the data is being attached.

RELOBJIDS

This value will be set only when data is being attached to a relationship (such as when Constraint Anchor DOP is connected to the second, third, of fourth inputs of a Constraint DOP).

In this case, this value is set to a string that is a space separated list of the object identifiers for all the Affected Objects of the relationship to which the data is being attached.

RELOBJNAMES

This value will be set only when data is being attached to a relationship (such as when Constraint Anchor DOP is connected to the second, third, of fourth inputs of a Constraint DOP).

In this case, this value is set to a string that is a space separated list of the names of all the Affected Objects of the relationship to which the data is being attached.

RELAFFOBJIDS

This value will be set only when data is being attached to a relationship (such as when Constraint Anchor DOP is connected to the second, third, of fourth inputs of a Constraint DOP).

In this case, this value is set to a string that is a space separated list of the object identifiers for all the Affector Objects of the relationship to which the data is being attached.

RELAFFOBJNAMES

This value will be set only when data is being attached to a relationship (such as when Constraint Anchor DOP is connected to the second, third, of fourth inputs of a Constraint DOP).

In this case, this value is set to a string that is a space separated list of the names of all the Affector Objects of the relationship to which the data is being attached.

ST

This value is the simulation time for which the node is being evaluated.

This value may not be equal to the current Houdini time represented by the variable T, depending on the settings of the DOP Network Offset Time and Time Scale parameters.

This value is guaranteed to have a value of zero at the start of a simulation, so when testing for the first timestep of a simulation, it is best to use a test like $ST == 0 rather than $T == 0 or $FF == 1.

SF

This value is the simulation frame (or more accurately, the simulation time step number) for which the node is being evaluated.

This value may not be equal to the current Houdini frame number represented by the variable F, depending on the settings of the DOP Network parameters. Instead, this value is equal to the simulation time (ST) divided by the simulation timestep size (TIMESTEP).

TIMESTEP

This value is the size of a simulation timestep. This value is useful to scale values that are expressed in units per second, but are applied on each timestep.

SFPS

This value is the inverse of the TIMESTEP value. It is the number of timesteps per second of simulation time.

SNOBJ

This is the number of objects in the simulation. For nodes that create objects such as the Empty Object node, this value will increase for each object that is evaluated.

A good way to guarantee unique object names is to use an expression like object_$SNOBJ.

NOBJ

This value is the number of objects that will be evaluated by the current node during this timestep. This value will often be different from SNOBJ, as many nodes do not process all the objects in a simulation.

This value may return 0 if the node does not process each object sequentially (such as the Group DOP).

OBJ

This value is the index of the specific object being processed by the node. This value will always run from zero to NOBJ-1 in a given timestep. This value does not identify the current object within the simulation like OBJID or OBJNAME, just the object’s position in the current order of processing.

This value is useful for generating a random number for each object, or simply splitting the objects into two or more groups to be processed in different ways. This value will be -1 if the node does not process objects sequentially (such as the Group DOP).

OBJID

This is the unique object identifier for the object being processed. Every object is assigned an integer value that is unique among all objects in the simulation for all time. Even if an object is deleted, its identifier is never reused.

The object identifier can always be used to uniquely identify a given object. This makes this variable very useful in situations where each object needs to be treated differently. It can be used to produce a unique random number for each object, for example.

This value is also the best way to look up information on an object using the dopfield expression function. This value will be -1 if the node does not process objects sequentially (such as the Group DOP).

ALLOBJIDS

This string contains a space separated list of the unique object identifiers for every object being processed by the current node.

ALLOBJNAMES

This string contains a space separated list of the names of every object being processed by the current node.

OBJCT

This value is the simulation time (see variable ST) at which the current object was created.

Therefore, to check if an object was created on the current timestep, the expression $ST == $OBJCT should always be used. This value will be zero if the node does not process objects sequentially (such as the Group DOP).

OBJCF

This value is the simulation frame (see variable SF) at which the current object was created.

This value is equivalent to using the dopsttoframe expression on the OBJCT variable. This value will be zero if the node does not process objects sequentially (such as the Group DOP).

OBJNAME

This is a string value containing the name of the object being processed.

Object names are not guaranteed to be unique within a simulation. However, if you name your objects carefully so that they are unique, the object name can be a much easier way to identify an object than the unique object identifier, OBJID.

The object name can also be used to treat a number of similar objects (with the same name) as a virtual group. If there are 20 objects named "myobject", specifying strcmp($OBJNAME, "myobject") == 0 in the activation field of a DOP will cause that DOP to operate only on those 20 objects. This value will be the empty string if the node does not process objects sequentially (such as the Group DOP).

DOPNET

This is a string value containing the full path of the current DOP Network. This value is most useful in DOP subnet digital assets where you want to know the path to the DOP Network that contains the node.

Note

Most dynamics nodes have local variables with the same names as the node’s parameters. For example, in a Position node, you could write the expression:

$tx + 0.1

…to make the object move 0.1 units along the X axis at each timestep.

Dynamics nodes